Swagelok fittings tightening instructions. Insert the tube with pre-swage...

Swagelok fittings tightening instructions. Insert the tube with pre-swaged ferrules into the fitting until the front ferrule seats against the fitting body; rotate the nut finger-tight. / 25 mm Swagelok® Tube Fittings Preswage the ferrules onto the tube using a Swagelok multihead hydraulic swaging unit (MHSU). The position of the ferrule sets This guide includes instructions for safe practice and installation of Swagelok tube fittings, O-seal male connectors, caps and plugs, port connectors, tube Subject: Swagelok® Tube Fittings - Tightening Instructions. It These instructions apply to both traditional fittings and to fittings with the advanced back-ferrule geometry. Disassembly before use is See the instructions starting below for installation of Swagelok tube fittings, O-seal male connectors, caps and plugs, port connectors, tube adapters, positionable elbows and tees, weld fittings, depth At Swagelok, we provide quality components and encourage our customers to train their installers on proper installation, including tubing selection and preparation, as well as the Swagelok tube fitting While holding fitting body steady, tighten the nut one-quarter turn. See how the two-ferrule design can be disassembled and reassembled. Do not use the Swagelok gap inspection gauge with Swagelok’s tube fittings are developed with such stringent control over all variables that a gap inspection gauge can be used to ensure proper tightening when the fittings are first installed. ; 2, 3, and 4 mm tube fittings, tighten the nut one-eighth turn. Fully insert the tubing into the fitting and against the shoulder; rotate the nut finger-tight . The Tube Fitter's Manual contains information on specifying Swagelok tube fittings and proper installation and use of high-quality tubing. Note: For 1/16, 1/8, and 3/16 in. /25 mm These instructions apply both to traditional fittings and to fittings with the advanced back-ferrule geometry. While holding the fitting body steady, tighten the nut 1 and 1/4 turns to the 9 o’clock position. Tighten Swagelok fittings to a torque spec, not infinite tightness. SwagelokTM instructions (for metal ferrules) When assembled correctly, SwagelokTM fittings form a leak tight seal and can be re-tightened many times. While holding the fitting body steady, How To Tighten Swagelok Fittings? This video provides a step-by-step guide on how to properly install a ¼- to 1-inch tube fitting using Swagelok. Make sure that the tubing rests firmly on the shoulder of the tube fitting body and that the nut is finger-tight. Safe practices and proper installation are imperative to the performance of the Swagelok Insert tubing into the Swagelok tube fitting. If the gauge will enter the gap, additional Additional regional languages may be available on your local Swagelok Sales and Service Center's websites. Fully insert the tube See the instructions starting on the next page for installation of Swagelok tube fittings, O-seal male connectors, caps and plugs, port connectors, tube adapters, positionable elbows and tees, weld Note: Make all connections with two wrenches, do not allow the fittings to turn or twist when tightening. or 25 mm and under Swagelok tube fittings come to you completely assembled, finger-tight and are ready for immediate use. For additional Use the Swagelok multihead hydraulic swaging unit (MHSU) in accordance with its furnished instructions to swage the ferrules onto the tubing. Swagelok® tube fittings Installation Instructions Swagelok tube fittings 1 in. If the gauge will not enter the gap, the fitting is sufficiently tightened. While holding Swagelok Tube Fittings Mark the nut at the 6 o’clock position. You are leaving the Swagelok Calgary site for the Swagelok corporate site. Do not use the Swagelok gap inspection gauge with While holding fitting body steady, tighten the nut one-quarter turn. Make sure that the tubing rests firmly on the shoulder of the tube fitting body These instructions apply both to traditional fittings and to fittings with the advanced back-ferrule geometry . Mark the nut at the 6 o’clock position. Scribe the nut at the 6 o’clock position. This technical bulletin is issued to provide information on proper installation and make-up of Swagelok® tube fittings. ; 2, 3, and 4 These instructions apply both to traditional fittings and to fittings with the advanced back-ferrule geometry. Tube Fitting Installation and Reassembly Safety Instructions Up to 1 in. Tools, steps to assemble a Swagelok tube fitting. Do not assemble and tighten fittings when system is pressurized. The combination of these Swagelok’s tube fittings are developed with such stringent control over all variables that a gap inspection gauge can be used to ensure proper tightening when the fittings are first installed. For 1/16, 1/8, and 3/16 in. Do not bleed system by loosening fitting nut or fitting plug. Apply the lubricant packaged with the Position the Swagelok gap inspection gauge next to the gap between the Nut and Body. After swaging: Apply the enclosed lubricant sparingly to the . Get a pocket guide and Installation Instructions Over 1 in. Fully insert the tube into the fitting and against the shoulder; rotate the nut finger-tight. gwdocipt kvvy pze kfubxcoe opdntd ewmttn skcrw dyefz mqww wopqmmv